The pad warning light only comes on if theres a break in the wiring somewhere this is how they work when the pads get low the disc wears through the little pad wiring loop and causes an open circuit which causes the warning lamp to come on. Ford Transit Custom 280S Trend 105ps Does this train stop on Merseyside.
2020 Ford Transit Custom Service Light Reset Procedure Youtube
Once the brake pads and wear sensors are replaced reset the brake pad warning system by turning the ignition switch to the on position.
. The system is working correctly or is currently in use. Ford Transit Forum. The fair city o Perth.
Reset button to acknowledge them. To reset the brake pad warning light on a 2015 ford transit you should take the following steps. In order to reset the Ford Transit Custom brake pad warning light the worn pads must be replaced.
Replace any worn brake pads. No stupid brake warning light for me anymore. Wed Aug 06 2008 819 pm Location.
Easy DIY about how to turn off the brake warning light lamp on the instrument cluster. Low brake pad warning light. Mar 09 2015 2009 Ford Transit Connect.
By loot Sat Sep 08 2018 1049 pm. Replace the wear wires on the brake pads if the the rear not got 1 need to get a plug that just loops around so it completes the circuit and the light should go out. Brake pad warning light.
The shop recommended that I replace the brake pads. Many braking systems use the same light to indicate a low level in the master cylinder. Discussion Starter 1 Dec 6 2021.
It could also be a sensor fault but as its a safety issue I would check the master cylinder level and for any leaks. The lights on a Ford dashboard follow a traffic light colour system. If the light is still present you can use a thin small screwdriver to clean them out then spray some wd40 in after then clip it.
Doing so may lead to injury when the brakes fail. The accelerator and the foot. Service the brakes according to the problem diagnosed by the code.
Only show this user. Driven over something that has slice through the brake pad warning light its not the sensor cable its the actual loom above the connecter for the sensor that goes to the wheelive had to cut the wires back and join them. It took a month and a half to get the pads they did the work and the brake pad warning still comes on each time I start the.
Brake pad warning light. I was led to belive that the sensors were diagonally opposed NSF OSR mine has just put the light on again for the back brakes although I ran about 3000 with the light on for the front and there was still about 2mm on the pads when they came off. To reset the low brake pad indicator on 2010 Ford Trans IT simply turn on the ignition and press the foot brake and the accelerator simultaneously.
Yes can be a few things Ive even replaced pads and when plugging in the new loom connector 1 of the pins was bent and it clipped shut but obviously open circuit. Ake Site Moderator Posts. If the light is still present you can use a thin small screwdriver to clean them out then spray some wd40 in after then clip it all back together.
Something is not working correctly - take extra care and check it out as soon as possible. I hope its only a faulty sensor. Ford Transit Connect Brake Warning Light Causes.
As long as continuity to ground exists through all the brake pad wear sensors the system should reset and the. Ford Transit Forum. Attach the OBD scanner back to the port and turn the key in the ignition again without starting the engine.
The brake warning light indicates that your Transit Connect has detected that one of its major brake components has failed typically detected. Replace any worn brake pads. This symbol will illuminate when a new message is stored within the information display.
The transit brake warning light on a Ford can be reset by changing the brake pads. The brake light is perhaps the most important warning light of all. By ake Mon Feb 02 2009 734 am.
When certain warning message appear in the display you must press the Set and. Press OK to read the code then press Delete to clear the Brake Warning light. It DOES NOT need the light reset by a dealer.
There is a serious and potentially dangerous problem - stop driving as soon as it is safe to do so. To reset the brake pad warning light on a 2015 ford transit you should take the following steps. How to reset brake pad warning light on ford transit.
Talking in general terms the brake pad wear warning lamp is activated by the disc wearing through a small loop of wire embeded in the pad. Now the annoying warning alarm on dash will not go off. If the warning light remains on even after replacing the pads the wear sensor may need to be replaced.
Thanked 1 Time in 1 Post. Although a brake fluid leak is often indicated by a soft brake pedal. 65 290 22 125ps custom with 2 side doors.
Once the loop is broken the lamp will stay lit. We do not recommend driving with this light on at all. By Jeroen Sun Jul 24 2011 723 pm 1 on failing on back axle.
Stop brake pad wear indicator warning. I took my 2020 Transit 250 to the local shop at 36K because the brake pad warning message was on. How to reset the service warning on a 2017 transit custom.
This can be done on any make and model car even newer ones Sup. Ford Transit Connect Message Indicator Dashboard LIGHT. 56 350 22 130ps mk7 with 2 side doors.
Youll get the same effect if any of the wires to the pad have become damagedbrokendislodged during your dunking in the floodwater. If the warning light is still on after changing the brake pads remove the fuse for 10 seconds.
Brake Pad Wear Indicator Repair Youtube
Mk7 Ford Transit Service Light Reset Procedure Youtube
Service Light Reset Ford Transit Youtube
How To Reset Service Light On 2016 Ford Transit How To Do A Dash Board Test Light Haulage Uk Youtube
0 Comments